Redwood Fencing Cost and Price Guide for American Homeowners 2026
This article breaks down the typical cost of redwood fencing in the United States, including how price scales by size, style, and labor. Buyers will see clear ranges for materials, posts, fasteners, and installation to help budget accurately. The cost discussion uses standard assumptions for 6-foot privacy fencing with pressure-treated supports avoided when possible to maximize redwood value.
Understanding the cost of redwood fencing helps buyers compare quotes, plan a reasonable budget, and spot common price drivers such as board width, fence height, and finish options.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Installed fence (per linear ft) | $15 | $28 | $40 | 6′ height, standard pressure-treated posts optional upgrade |
| Material only per linear ft | $8 | $14 | $22 | Western red cedar look-alike; redwood typically at higher end |
| Post cost per post | $20 | $40 | $70 | 4×4 or 6×6, set in concrete |
| Hardware per linear ft | $2 | $4 | $8 | Screws, nails, rails, caps |
| Prep and removal old fence | $1,200 | $2,500 | $4,500 | Depends on site and debris |
What buyers usually pay for redwood fencing
Typical total price for a standard 100-foot fence installed ranges from $2,800 to $4,000, with average around $3,400. This includes materials, labor, and basic staining or sealing. Shorter or cheaper installations in rural areas tend to land on the low end, while larger or higher-spec setups near metropolitan regions push toward the high end. The main cost drivers are fence height, board width, panel style (privacy vs board-on-board), post spacing, and whether a gate is included.
Assumptions: standard 6-foot privacy panels, 4×4 posts set in concrete, no specialty carpentry, mid-range stain, and no permit fees in non-expedited markets. If stain or sealant is included, expect a per-lineal-foot add-on of $1-$2.
Cost components readers should expect in a redwood fence quote
Material costs usually form the largest share, followed by labor and permit-related fees where applicable. The table below breaks out typical components for a mid-range project in suburban markets.
| Component | Low | Average | High | Notes |
|---|---|---|---|---|
| Materials (boards, rails, posts) | $8-$14/ft | $12-$18/ft | $18-$22/ft | Higher costs for wider boards or higher-grade heartwood |
| Labor (installation) | $6-$12/ft | $10-$16/ft | $16-$24/ft | Includes frame assembly and alignment |
| Posts and concrete | $40-$60/post | $45-$65/post | $65-$90/post | Concrete mix and footing depth vary by soil |
| Hardware and fasteners | $1-$2/ft | $2-$4/ft | $4-$8/ft | Stainless or coated options cost more |
| Stain/sealant | $0.50-$1.00/ft | $1.00-$2.00/ft | $2.50-$4.00/ft | Labor included if applied |
| Removal of old fence | $1,000 | $2,000 | $3,000 | Not always needed; varies by site |
Assumptions: median climate, average soil, standard 4×4 posts, no custom milling.
Key cost variables that most influence quotes
Height, board width, and panel style are the top three cost levers in redwood fencing quotes. A 6-foot privacy panel uses more material and longer labor time than a 4-foot picket, and wider boards raise both material and shipping costs. SEER-like efficiency is not a factor here, but access and terrain add notable margins.
Region and labor market impact on redwood fence pricing
Coastal or metropolitan markets typically see higher installed price ranges than rural inland areas. The difference often reflects higher labor costs and materials logistics. For example, a 100-foot project in a coastal city may run 15-25% above a similar job in a small inland town, all else equal. Seasonal demand can also widen spreads in spring and early summer.
Concrete decisions to lower the redwood fence cost
Smart scope adjustments can trim total costs without sacrificing essential function. Consider shorter spans, fewer gates, using standard post spacing, and selecting a mid-range staining option. Delaying installation until demand softens and comparing multiple quotes also yields savings.
What a typical quote breaks down by line item
A line-item view helps compare quotes side by side and detect overcharges. The example below reflects a 100-foot, 6-foot privacy install in a suburban area with standard 4×4 posts and concrete.
| Line Item | Low | Average | High | Perimeter Notes |
|---|---|---|---|---|
| Materials (boards, rails, posts) | $1,200-$1,400 | $1,800-$2,000 | $2,200-$2,400 | Board width 5.5 in typical |
| Labor | $600-$1,100 | $1,100-$1,600 | $1,900-$2,400 | Includes framing and alignment |
| Post installation | $200-$400 | $350-$600 | $700-$1,000 | Concrete footing included |
| Hardware | $60-$120 | $120-$180 | $240-$320 | Stainless steel options vary |
| Stain/sealant | $60-$120 | $120-$200 | $240-$360 | Includes labor where noted |
Regional pricing deltas you may see in the U.S.
Prices commonly swing by region due to labor rates, material transport, and permit practices. The table shows typical regional deltas relative to a national baseline for a 100-foot, 6-foot fence.
| Region | Low | Average | High | Notes |
|---|---|---|---|---|
| Midwest suburban | $2,900 | $3,500 | $4,100 | Balanced labor and material costs |
| West Coast urban | $3,600 | $4,300 | $5,500 | Higher wages and logistics |
| Northeast metro | $3,400 | $4,000 | $5,000 | Permitting and disposal fees can apply |
| South rural | $2,600 | $3,100 | $3,700 | Lower labor, potential material savings |
Labor considerations that affect the price tag
Crew size, task complexity, and scheduling windows shift the final price. A two-person crew may take longer on a larger property, while a single-trade setup can reduce overhead but might extend completion time. For 100 feet, expect 1-2 days with a two-person crew under normal conditions.
Protecting value: maintenance and lifecycle costs
Redwood fencing lasts well when maintained, so budgeting for a seal or stain every 3-5 years helps preserve aesthetics and resale value. Maintenance adds $0.50-$2.00 per foot every few years, depending on climate exposure and coating quality. Plan for a mid-life refresh rather than full replacement to maximize return on the initial investment.
Three real-world quote scenarios to compare
Realistic quotes illustrate how scope shifts affect price.
- Scenario A: 80 feet, 6-foot privacy, standard posts, no gate. Materials $1,120; Labor $860; Hardware $120; Stain $120. Total $2,220.
- Scenario B: 120 feet, 6-foot privacy, two gates, premium posts, with staining. Materials $2,100; Labor $1,700; Hardware $260; Stain $260. Total $4,320.
- Scenario C: 100 feet, 4-foot panel, board-on-board style, set in rural area. Materials $1,100; Labor $1,000; Post $420; Stain $120. Total $2,640.
Assumptions: standard 6-foot panels, 4×4 posts, concrete footings, no underground obstacles, average soil conditions.
Perimeter planning: how many posts and rails you’ll need
Proper spacing minimizes material waste and labor time. For 8-foot panels with 8-foot post spacing, you’ll typically require one post every 8 feet plus end posts, which affects both material costs and installation effort.
Finish options and their price impact
Stain or sealant adds cost but preserves redwood’s color and resistance to weather. Clear finishes tend to be cheaper upfront, while tinted or opaque stains can add $0.50-$1.50 per foot in materials and labor, depending on the number of coats.
How to compare quotes effectively
Use a side-by-side table that shows material type, board width, post style, finish, and per-foot vs total pricing. Ask contractors to list any disposal, site prep, or permit fees separately to avoid hidden charges.