1 1/8 Plywood Price and Cost Guide for U.S. Buyers 2026
Buyers typically pay for 1 1/8 inch plywood per sheet, with costs driven by grade, species, and regional labor rates. The price range reflects sheet costs, delivery, and potential disposal fees. This article presents current cost estimates to help plan a budget for 4×8 sheets and related materials.
Assumptions: Midwest or Southern pricing, standard 4×8 sheets, exterior-grade plywood for structural use, normal access, typical delivery within 50 miles.
Price ranges per 4×8 sheet of 1 1/8″ plywood
Typical total price per sheet spans from a low to high range due to species and grade differences. Low: $40-$60, Average: $70-$95, High: $110-$120 per sheet for premium exterior-grade panels. For quick budgeting, use about $1.25-$2.50 per square foot when comparing to other thicknesses.
Material grade and species impact on cost for 1 1/8″ plywood
The cost varies with grade (A, B, C, or No. 2) and species (oak, pine, birch, or hardwood plywood). A typical 4×8 sheet in 1 1/8″ thickness runs $40-$60 for economy pine, $75-$95 for birch or alder, and $110-$120 for premium hardwood exterior panels. Assumptions: Standard veneer core, exterior-grade glue, mid-range hardness.
Regional price differences for 4×8 sheets
Geography matters: coastal cities or regions with higher labor costs push sheet prices higher. In the U.S., expect per-sheet ranges of $50-$60 in lower-cost regions, $75-$95 in mid-cost regions, and $100-$120 in high-cost metro areas. Assumptions: urban delivery adds freight, regional lumber supply affects base price.
Delivery and handling charges for heavy 1 1/8″ plywood
Delivery fees typically run $25-$60 per order, with higher charges for remote or residential delivery. Offload time and packaging add-ons can raise costs by $10-$25. If multiple sheets are purchased, bulk delivery often lowers per-sheet delivery cost.
Labor and installation costs when installing 1 1/8″ plywood
Install labor for sheet-plywood work can range from $0.50-$1.25 per square foot for basic handling to $2.00-$4.00 per square foot for precise cuts, edge finishing, or subfloor installation. A typical project using 4×8 sheets may add $80-$350 in labor, depending on access, fasteners, sealant, and surface preparation. Assumptions: Standard tools, no heavy structural modifications, residential site.
Taxes, permits, and disposal costs tied to 1 1/8″ plywood projects
Sales tax on building materials in most states ranges from 0% to 10%, with some exemptions for contractors in certain projects. Permits are rarely required for simple plywood replacement but may apply for structural renovations. Disposal or recycling fees typically run $5-$15 per sheet if city curbside service is used. Assumptions: Non-structural use, single-family home, standard waste removal.
Comparing 1 1/8″ plywood to alternate panels for cost control
As a cost control strategy, compare with 1/4″ or 1/2″ plywood combined with a plywood-backed panel, or with oriented strand board (OSB) alternatives. A typical OSB 1/2″ panel can be $15-$25 per sheet, while 1 1/8″ thick plywood usually averages $40-$120 per sheet. When used as a structural layer, thickness and fastener requirements must be considered. Assumptions: Structural compatibility and load requirements match local building codes.
Per-unit pricing: calculating cost per square foot for planning
Per-square-foot pricing helps when comparing to other thicknesses or panel types. For 1 1/8″ plywood, expect roughly $1.25-$2.50 per sq ft under typical conditions. A 4×8 sheet covers 32 sq ft, translating to $40-$80 per sheet in low ranges and $100-$120 in premium scenarios. Assumptions: Standard installation and full 32 sq ft coverage per sheet.
Scenarios: when 1 1/8″ plywood makes financial sense
In structural subfloors, bracing, or formwork where thicker panels are mandated, 1 1/8″ plywood provides strength without oversizing. A common scenario costs around $60-$95 per sheet for economy-grade installations and $110-$120 for exterior-grade, moisture-resistant applications. Planning should estimate labor and delivery together with material. Assumptions: Residential construction with standard joist spacing and moisture exposure.
Cost-saving moves: how to lower the price on 1 1/8″ plywood
To reduce total expense, consider buying in bulk, timing shipments during lower-demand months, selecting standard grades, and consolidating delivery. Concrete steps include choosing economy-grade plywood for noncritical layers, coordinating with other trades to minimize site visits, and combining orders to reduce freight. Typical savings can range from 5% to 15% off material cost when practices are applied. Assumptions: Moderate project size, standard access, no urgent delivery.
Summary table
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| 1 1/8″ plywood sheet 4×8 (material only) | $40 | $70 | $120 | Economy to premium exterior grades |
| Delivery/handling per order | $25 | $40 | $60 | Distance and accessibility vary |
| Installation labor (per sq ft) | $0.50 | $1.00 | $4.00 | Includes cutting and fastening |
| Taxes (material) | $0 | $0-$5 | $10 | State-dependent |
| Total project per sheet (material + delivery + labor) | $70 | $111 | $194 | Assumes typical 32 sq ft coverage |